Kirk SSS-V2 safety stop screws version 2 for lens plates and camera plates from Kirk

Kirk SSS-V2 Safety Stop Screws Version 2 for lens plates and camera plates from Kirk

You know how it is: the clamp is opened just a tick too far, you take your eyes off the camera for a moment, a small bump, and the quick-release plate slips sideways out of the mount. This is exactly where the Kirk SSS-V2 Safety Stop Screws Version 2 come into play and make sure that your camera or telephoto lens doesn’t suddenly head toward the ground.

The Kirk SSS-V2 were developed specifically for all Kirk camera and lens plates that have matching threaded holes for safety stops. They sit at the ends of the centrally recessed slots of the quick-release plates and prevent the plate from sliding out sideways when the clamp is only slightly opened. The screw heads hit the stop in time before anything happens. Very unspectacular, but extremely effective.

Maximum safety for your quick-release plate

In practice, this means: even if you loosen your Arca-style compatible clamp just a bit to correct the position, the plate remains guided. The Safety Stop Screws act like a small mechanical stop sign that blocks accidental slipping out. Especially with heavier setups with long telephoto lenses or during outdoor shoots on uneven ground, this extra protection is more than just nice to have – in case of doubt, it’s what saves your gear.

We’d say it’s the kind of detail you install once and then almost forget about until you find yourself in a tricky situation and realize that it’s precisely these small screws that are making the difference. And yes, it’s really astonishing how much peace of mind two tiny socket head cap screws can provide.

Compatible with Kirk lens plates and camera plates

The Kirk SSS-V2 Safety Stop Screws Version 2 fit all Kirk camera and lens plates that are equipped with threaded holes for safety stops. If your plate has these holes, you can use the SSS-V2 right away. This allows them to integrate seamlessly into existing Kirk quick-release systems and add an extra level of safety to your Arca-style setup without requiring any other changes to your workflow.

Especially if you frequently work with a tripod, gimbal, or ball head, this type of safety stop is not a luxury but a sensible upgrade to reliably secure your camera equipment.

Precision socket head cap screws with 4-40 UNC thread

The set includes two socket head cap screws with 4-40 UNC thread. This fine thread is matched exactly to the corresponding Kirk threaded holes and ensures a clean, play-free fit. The screws are robust, durable, and designed for long-term use, so you don’t have to constantly retighten or replace them.

Thanks to the socket head design, they can be gripped securely and screwed in in a controlled manner. At the same time, they remain compact enough not to get in the way during everyday use or catch when inserting the plate into the clamp. A small but very well thought-out solution for more safety on your quick-release plate.

Including matching hex key

So you can get started right away, the set includes a matching hex key. You don’t have to rummage through your toolbox or try out random hex keys. Just lay the plate ready, position the screws, tighten them with the included key, and you’re done.

This small extra may sound unspectacular, but it ensures that installation is completed in just a few minutes. It’s especially practical when you’re on the go, for example when traveling or on set, and want to install the Safety Stop Screws directly on location.

Robust quality, developed for everyday photographic use

The Kirk SSS-V2 Safety Stop Screws are clearly designed for demanding photographic use. They easily withstand repeated tightening and loosening, cope with frequent changes of location, and handle rougher outdoor conditions. Rain, dust, cold – under normal circumstances, none of this is a big deal for these little helpers.

We see them as a kind of insurance for your camera and lens plates: unobtrusive, lightweight, quick to install, but extremely valuable in an emergency. Especially if you use high-end DSLR or mirrorless camera systems with expensive lenses, this additional level of safety makes a lot of sense.

Practical addition for Arca-style compatible setups

If you’re already working with Arca-style compatible quick-release plates and clamps, the Kirk SSS-V2 Safety Stop Screws Version 2 integrate seamlessly into your existing system. They neither change the basic handling nor the balance of your camera; they simply add a mechanical safety stop to your setup.

Especially when frequently switching between portrait and landscape orientation, shooting panoramas, or recording video on a tripod, it’s reassuring to know that the plate cannot slide sideways out of the clamp, even if you briefly loosen it to correct the position.

Scope of delivery of the Kirk SSS-V2 Safety Stop Screws Version 2

The scope of delivery includes all components you need for immediate use:

• 1 x matching hex key for installation
• 2 x socket head cap screw with 4-40 UNC thread as Safety Stop Screws

That’s all it takes to equip your Kirk camera or lens plates with a reliable safety stop and effectively prevent them from slipping out sideways when the clamp is slightly opened.

Quality, developed and manufactured in the USA

The Kirk SSS-V2 Safety Stop Screws Version 2 come from the same quality philosophy as the well-known Kirk lens plates and camera plates. Manufacturing in the USA stands for precise workmanship, reliable fit, and a consistently practice-oriented design. You can see it in the details: clean threads, accurate tolerances, and a construction that simply works in everyday use.

If you value durable accessories that meaningfully complement your camera equipment, these Safety Stop Screws are a small but very effective investment in more safety and stability on your tripod head.